Watlow CLS200, MLS300 and CAS200 Manual do Utilizador Página 66
- Página / 92
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
60 Communications Specification
Chapter 3: Controller Parameter Descriptions
• Range: 0 to 255.
• Default: 5.
Startup Alarm Delay (40)
This parameter designates a delay time for process and deviation alarms
on power-up. The controller does not report process and deviation
alarms for the specified number of minutes after the controller powers
up.
The startup alarm delay is a global alarm parameter; it applies to all
process and deviation alarms for every loop.
The startup alarm delay does not apply to failed-sensor alarms and AIM
failure alarms.
• Range: 0 to 255 minutes.
• Default: 0.
High Process Alarm Output Number (41)
This parameter assigns the output number to which the high process
alarm output is directed.
• Range: 0 to 34.
• Default: 0 (no high process alarm output).
Low Process Alarm Output Number (42)
This parameter assigns the output number to which the low process
alarm output is directed.
• Range: 0 to 34.
• Default: 0 (no low process alarm output).
High Deviation Alarm Output Number (43)
This parameter assigns the output number to which the high deviation
alarm output is directed.
• Range: 0 to 34.
• Default: 0 (no high deviation alarm output).
Low Deviation Alarm Output Number (44)
This parameter assigns the digital output number to which the low
deviation alarm output is directed.
• Range: 0 to 34.
- CLS200, MLS300 1
- Communications 1
- Specification 1
- Warranty 2
- Contents 3
- Protocol Syntax 9
- Transaction Sequence 10
- Packet Format 12
- Codes in a Packet 12
- Error Checking 14
- Cyclic Redundancy Check (CRC) 15
- Examples 16
- Block Write 19
- Message Data 20
- Data for a Write Command 21
- Two-Byte Data Types 21
- Figuring Block Size 21
- Anafaze/AB Data Table Summary 22
- Number Description 24
- Address 24
- Type Number of Bytes 24
- Overview 27
- The Query-Response Cycle 28
- Serial Transmission 28
- Message Framing 29
- Contents of the Data Field 30
- CRC Error Checking 31
- Function Codes 32
- Diagnostic Subfunctions 33
- Writing Data 36
- Reading Data 36
- Write Examples 38
- Modbus-RTU Data Table Summary 39
- Chapter 3: 45
- All Units 17, 18 47
- Enhanced Features options 49
- Parameters (by number) 51
- Input Type (3) 52
- Output Type (4) 53
- Setpoint (5) 54
- Process Variable (6) 54
- Output Filter (7) 54
- Output Value (8) 55
- Alarm Deadband (12) 55
- Alarm_Status (13) 56
- Ambient Sensor Readings (15) 58
- Pulse Sample Time (16) 58
- High Process Variable (17) 58
- Low Process Variable (18) 58
- Precision (19) 59
- Cycle Time (20) 60
- Zero Calibration (21) 60
- Full Scale Calibration (22) 60
- Digital Inputs (25) 60
- Digital Outputs (26) 61
- Override Digital Input (28) 61
- Override Polarity (29) 61
- System Status (30) 62
- System Command Register (31) 62
- Data Changed Register (32) 63
- Input Units (33) 63
- EPROM Version Code (34) 64
- Options Register (35) 64
- High Reading (37) 65
- Low Reading (38) 65
- Heat/Cool Spread (39) 65
- Startup Alarm Delay (40) 66
- • Range: See tables below 67
- • Default: 0 67
- Current Segment (47) 68
- Segment Time Remaining (48) 68
- Current Cycle Number (49) 68
- Tolerance Alarm Time (50) 68
- Last Segment (51) 68
- Number of Cycles (52) 69
- Ready Setpoint (53) 69
- Ready Event States (54) 69
- Segment Setpoint (55) 70
- Segment Time (58) 72
- Tolerance (59) 72
- Ramp/Soak Flags (60) 72
- Output Limit (61) 73
- Output Limit Time (62) 73
- Alarm_Control (63) 74
- Alarm_Acknowledge (64) 74
- Alarm_Mask (65) 74
- Alarm_Enable (66) 74
- AIM Fail Output (68) 75
- Output Linearity Curve (69) 76
- SDAC Mode (70) 76
- SDAC Low Value (71) 76
- SDAC High Value (72) 76
- Save Setup to Job (73) 77
- Input Filter (74) 77
- Loop Alarm Delay (75) 77
- Loop Names (77) 77
- Channel Name (78) 78
- Manufacturing Test (80) 78
- Cascade Maximum Setpoint (89) 80
- Cascade Base Setpoint (87) 80
- Cascade Minimum Setpoint (88) 80
- Loop Status (96) 82
- Output Type/Disable (97) 82
- Output Reverse/Direct (98) 82
- Controller Type (99) 83
- Ramp/Soak Profile Number (100) 83
- Controller Address (101) 83
- Baud Rate (102) 83
- Ready Events (103) 84
- Appendix A: 85
- Communications Driver 85
- Close_Comm_Port() 86
- DownLoad() 86
- UpLoad() 87
- Glossary 89
Manuais e produtos relacionados com Sensores Watlow CLS200, MLS300 and CAS200
Sensores Watlow CLS Manual do Utilizador
(180 páginas)
(180 páginas)
Sensores Watlow CLS200 Manual do Utilizador
(251 páginas)
(251 páginas)
(2 páginas)
(2 páginas)
(2 páginas)
Sensores Watlow CPC400 Manual do Utilizador
(230 páginas)
(230 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais