Watlow DIN-A-MITE Style C Manual do Utilizador descarregar pdf (Página 18)

WATLOW DIN-A-MITE Style C User's Manual

Declaration of Conformity

DIN-A-MITE

“C” Power Controller

WATLOW an ISO 9001approved facility since 1996.

1241 Bundy Blvd.

Winona, MN 55987 USA

Declares that the following product:

Designation: DIN-A-MITE “C” Power Control

Model Numbers: DC(1, 2, 3, 8 or 9)(0, 1, 2, 3 or T) – (02, 12, 20, 24, 27, 40, 48 or 60)

(CX, K1, K2, K3, F X, SX) – (0, H or S)(followed by any 3 numbers or letters.)

X = any number 0 - 9

Classification: Power Control, Installation Category III, Pollution degree 2, IP20

Rated Voltage: 24 to 600 V~ (ac), 50/60 Hz

Meets the essential requirements of the following European Union Directives by using the relevant

standards show below to indicate compliance.

2004/108/EC Electromagnetic Compatibility Directive

EN 61326-1: 2005 Electrical equipment for measurement, control and laboratory use

– EMC requirements (Industrial Immunity, Class A

1,2,4

Emissions)

Not for use in a Class B environment without additional filtering.

EN 61000-4-2:2008 Electrostatic Discharge Immunity

EN 61000-4-3:2006 Radiated Field Immunity 10V/m 80 MHz- 1GHz, 3V/m 1.4GHz-2.7GHz

EN 61000-4-4:2011 Electrical Fast-Transient / Burst Immunity

EN 61000-4-5:2006 Surge Immunity

EN 61000-4-6:2008 Conducted Immunity

EN 61000-4-11:2004 Voltage Dips, Short Interruptions and Voltage Variations

EN 61000-3-2:2005 Harmonic Current Emissions

EN 61000-3-3:2005

EN 61000-3-11:2001

Voltage Fluctuations and Flicker

≤ 16A

Voltage Fluctuations and Flicker ≤ 75A with conditional connection

Notes

Use of an external filter is required to comply with conducted emissions limits. See note 4 below.

A Line Impedance Stabilization Network (LISN) was used for conducted emissions measurements.

To comply with flicker requirements, command signal models FX or SX will require a reduced source

impedance. Cycle time on ON/OFF models CX and K1, K2, K3 may need to be up to 175 seconds at 16A

or have a reduced source impedance.

2006/95/EC Low-Voltage Directive

EN 50178:1997 Electronic equipment for use in power installations.

Per 2002/96/EC W.E.E.E Directive Please Recycle Properly.

These devices contain lead solder and are not RoHS compliant.

They are a Control Device and fall outside the scope of 2002/95/EC Directive.

Required External EMI Filters for DIN-A-MITE with More Than 6 Amp Loads. An external ElectroMagnetic

Interference (EMI) filter must be used in conjunction with the DIN-A-MITE for loads in excess of six amperes

(6A) at 150 to 250 KHz. Watlow has verified that a tank filter will suppress EMI created by SCR power

controllers to comply with the conducted emissions limits. For graphic depictions of the filters in a circuit drawing

ee section entitled “Required External EMI Filters for DIN-A-MITE with More than 6A Loads”.

1 2 ... 13 14 15 16 17 18 19 20 21 22

Comentários a estes Manuais

Sem comentários

Watlow DIN-A-MITE Style C Manual do Utilizador Página 18

Comentários a estes Manuais

Manuais e produtos relacionados com Sensores Watlow DIN-A-MITE Style C