Watlow MINICHEF 2000 Manual do Utilizador descarregar pdf (Página 22)

Hardware & Software Setup Guide Watlow MINICHEF 2000 ■ 21

Function Parameter Value Your Setting

[tHErl] Thermal [tyPE`] Temperature Control Type PID, On-Off

[HYSt1] Hysteresis 1 1 to 99ºF (1 to 55ºC)

[HYSt2] Hysteresis 2 1 to 99ºF (1 to 55ºC)

[Pid`U] PID Units [```SI], [```US]

[tune1] Auto-tuning, Channel 1 [```on], [``OFF]

[tune2] Auto-tuning, Channel 2 [```on], [``OFF]

[ProP1] Proportional Band 1 1 to 999ºF (1 to 555ºC)

[rSEt1] Reset (integral) Gain 1 0.00 to 9.99 repeats/minute

[int`1] Integral Gain 1 0.00 to 99.99 minutes/repeat

[rAtE1] Rate (derivative) Gain 1 0.00 to 9.99 minutes

[dEr`1] Derivative Gain 1 0.00 to 9.99 minutes

[CYcL1] PID Cycle Time 1 1 to 60 seconds

[ProP2] Proportional Band 2 1 to 999ºF (1 to 555ºC)

[rSEt2] Reset (integral) Gain 2 0.00 to 9.99 repeats/minute

[int`2] Integral Gain 2 0.00 to 99.99 minutes/repeat

[rAtE2] Rate (derivative) Gain 2 0.00 to 9.99 minutes

[dEr`2] Derivative Gain 2 0.00 to 9.99 minutes

[CYcL2] PID Cycle Time 2 1 to 60 seconds

[`diag] WatHelp [date`] Date-of-Manufacture Code YYDDD

Diagnostics [Ser`n] Serial Number XXXXX

[Part1] Part Number-first F2XX

-XXXX-XXXX

four digits

[Part2] Part Number-middle F2XX-XXXX

-XXXX

four digits

[part3] Part Number-last F2XX-XXXX-XXXX

four digits

[S`reU] Software Revision Number XX

[idEnt] Key Function Identification Yes, no

[Appl`] Current Application XX

Number

[*•*••] Display Test All spot LEDs and all main-

display LEDs will light up

[Outpt] Output Test 0=All outputs are normal

1=Output 1 is on. All others

are off.

2=Output 2 is on. All others

are off.

3= Event Output 1 is on.

All others are off.

4=Event Output 2 is on.

All others are off.

5=Output 5 is on. All others

are off.

6=All outputs are on.

[inPut] Event Input Test 0=Both Event Inputs are off.

1=Event Input 1 is on.

2=Event Input 2 is on.

3=Both Event Inputs are on.

[teNp1] Actual Temperature XXXX ºF/ºC

Channel 1 (w/out offset)

[teNp2] Actual Temperature XXXX ºF/ºC

Channel 2 (w/out offset)

Step 3 Configure the Controller

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 70 71

Comentários a estes Manuais

Sem comentários

Watlow MINICHEF 2000 Manual do Utilizador Página 22

Comentários a estes Manuais

Manuais e produtos relacionados com Sensores Watlow MINICHEF 2000